DRJ18号 スペック
- 2019/02/20
- 21:41
DRJ18号（Eachine Wizard X220S） スペック
こちら ↓ にテスト記録がありました。
TEST: Eachine Wizzard X220S
Description:
Item Specification
Eachine Wizard X220S
Wheelbase: 220mm
Frame arm: 4mm carbon fiber
Weigh: 356g (without battery and camera mount)
Take off weigh: 561g
3K carbon fiber frame kit, 4mm thickness and 15mm width frame arms, the width is 10mm less than Eachine Wizard X220.
Frame kit with camera angle scale and 30° camera mount for Runcam 3 Gopro session.
Anti-vibration sponges to protect the racer frome crashing.
Eachine MN2206 2300KV motor
KV: 2300
Max thrust: 1100G
Length: 35MM
NO.OF cell: 3-5S
Diameter: 28MM
Framework: 12N14P
Shaft: 5mm
Propeller: 5 inch
Weight: 28g
Eachine 30A BLHELI_S 4 in 1 ESC （※ Dshot 600 ESC であること確認）
Con. current: 30A
Peak current (10S): 35A
Input voltage: 2-5S
BEC: 5V output
Programming: YES
Firmware: blheli_s
Weight: 28g
Size: 36*36MM
Eachine 1179 800TVL CCD camera
Color: purple
Sensor: CCD
Resolution(horizontal center): 800TVL
Shell size: 25mm*25mm
Weight: 11g
Resolution: PAL: 1980H×1080 (2MP)
Format: PAL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00 adjustable, up to 55dB.
AWB: ON/OFF
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: internal synchronization
Lens: standard 2.8mm lens
Working voltage: DC12V (Wide Voltage, measured that can be work in 5-13V)
Workig current: 70mA (low power consumption)
Workig temperature: -20℃--60℃
Humidity: 0%~98%
Strong backlighting effect
5.8G 40CH 25MW 200mw 600MW
switchable transmitter
Video transmitter
To access to the VTX setting, you will have first to remove the top canopy plate…
It’s a drawback especially in racing conditions. More be vigilant, when you remove
the plate to no break the coaxial connexion hot glued on the VTX.
The unique butoon is installed on top.
The button if shorly pressed can cycle between the eight frequencies inside
the current selected band.
If you press on it more than 3S, the current band sign will flash
then short press on the button to cycle over the 12 bands !!!!.
Finally if you very long press on it, you will be able to cycle between
the three output power: 25mW (1 bar = default setting), 200mW (2 bars)
and 600mW (3 bars).
Video Format : NTSC/PAL
Channel: 40CH
Operating Temperature : -10~85℃
Connector: RP-SMA Female
Antenna connector: RP-SMA Male
Omnibus F4 V3 flight controller
Size: 36x36mm
Mount holes: 30.5x30.5mm
STM32 F405 MCU, Runs Betaflight 3.0.1 firmware, could run faster loop time.
Using F4 MCU controls OSD over SPI bus in DMA mode.
OSD Configation has been included in Betaflight GUI.
SBUS/PPM input (Pinheaders)
6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
With barometer
SPI Sensor MPU6000
Included 128Mbit Flash, please always use BEC for the FC.
Supported by BETAFLIGHT and dRonin
Eachine 5051 3-blade propeller
Color: purple
Quantity: 10 Pairs
Mounting Hole: 5mm
This is the ARF version that comes without battery, charger, receiver and remote control.
Package included:
1 x Eachine Wizard X220S frame kit
2 x 2206 2300KV motor CW
2 x 2206 2300KV motor CCW
1 x Eachine 30A BLHELI_S 4 in 1 ESC
1 x Omnibus F4 V3 flight controller
1 x 1179 800TVL camera
1 x 5.8G 40CH 25MW 200mw 600MW switchable VTX
10 x Eachine 5051 3-blade propeller purple CW
10 x Eachine 5051 3-blade propeller purple CCW
1 x 30° Camera Mount(For Runcam3/Gopro session)
1 x Pagoda antenna
2 x Battery strap
2 x Wrench
(以下 参考データ）
ESC overview
CLI # diff all
diff all
# version
# Betaflight / OMNIBUSF4SD (OBSD) 3.5.6 Feb 16 2019 / 13:29:46 (c28ca22f9) MSP API: 1.40
board_name OMNIBUSF4SD
manufacturer_id
mcu_id 002b0049474b501620393257
signature
# reset configuration to default settings
defaults nosave
# name
name DRJ18_JE6RUX
# resources
# mixer
# servo
# servo mix
# feature
feature -RX_PARALLEL_PWM
feature -ANTI_GRAVITY
feature RX_SERIAL
feature LED_STRIP
# beeper
beeper -GYRO_CALIBRATED
beeper -ARMING_GPS_FIX
beeper -GPS_STATUS
beeper -ACC_CALIBRATION
beeper -ACC_CALIBRATION_FAIL
beeper -READY_BEEP
beeper -ARMED
beeper -ON_USB
beeper -BLACKBOX_ERASE
beeper -CRASH FLIP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSED
# beacon
# map
# serial
serial 5 64 115200 57600 0 115200
# led
led 0 0,0::CB:2
led 1 0,1::CB:2
led 2 0,2::CB:2
led 3 0,3::CB:2
led 4 0,4::CB:2
led 5 15,0::CB:2
led 6 15,1::CB:2
led 7 15,2::CB:2
led 8 15,3::CB:2
led 9 15,4::CB:2
# color
# mode_color
# aux
aux 0 0 0 1300 2100 0 0
aux 1 1 1 900 1300 0 0
aux 2 2 1 1300 1700 0 0
aux 3 13 3 1300 2100 0 0
aux 4 28 0 1700 2100 0 0
# adjrange
# rxrange
# vtx
# rxfail
# master
set serialrx_provider = SBUS
set osd_vbat_pos = 2081
set osd_tim_2_pos = 2103
set osd_flymode_pos = 2273
set osd_crosshairs_pos = 2253
set osd_craft_name_pos = 2497
set osd_warnings_pos = 2478
# profile
profile 0
# profile
profile 1
# profile
profile 2
# restore original profile selection
profile 0
# rateprofile
rateprofile 0
# rateprofile
rateprofile 1
# rateprofile
rateprofile 2
# rateprofile
rateprofile 3
# rateprofile
rateprofile 4
# rateprofile
rateprofile 5
# restore original rateprofile selection
rateprofile 0
# save configuration
save
#
こちら ↓ にテスト記録がありました。
TEST: Eachine Wizzard X220S
Description:
Item Specification
Eachine Wizard X220S
Wheelbase: 220mm
Frame arm: 4mm carbon fiber
Weigh: 356g (without battery and camera mount)
Take off weigh: 561g
3K carbon fiber frame kit, 4mm thickness and 15mm width frame arms, the width is 10mm less than Eachine Wizard X220.
Frame kit with camera angle scale and 30° camera mount for Runcam 3 Gopro session.
Anti-vibration sponges to protect the racer frome crashing.
Eachine MN2206 2300KV motor
KV: 2300
Max thrust: 1100G
Length: 35MM
NO.OF cell: 3-5S
Diameter: 28MM
Framework: 12N14P
Shaft: 5mm
Propeller: 5 inch
Weight: 28g
Eachine 30A BLHELI_S 4 in 1 ESC （※ Dshot 600 ESC であること確認）
Con. current: 30A
Peak current (10S): 35A
Input voltage: 2-5S
BEC: 5V output
Programming: YES
Firmware: blheli_s
Weight: 28g
Size: 36*36MM
Eachine 1179 800TVL CCD camera
Color: purple
Sensor: CCD
Resolution(horizontal center): 800TVL
Shell size: 25mm*25mm
Weight: 11g
Resolution: PAL: 1980H×1080 (2MP)
Format: PAL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00 adjustable, up to 55dB.
AWB: ON/OFF
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: internal synchronization
Lens: standard 2.8mm lens
Working voltage: DC12V (Wide Voltage, measured that can be work in 5-13V)
Workig current: 70mA (low power consumption)
Workig temperature: -20℃--60℃
Humidity: 0%~98%
Strong backlighting effect
5.8G 40CH 25MW 200mw 600MW
switchable transmitter
Video transmitter
To access to the VTX setting, you will have first to remove the top canopy plate…
It’s a drawback especially in racing conditions. More be vigilant, when you remove
the plate to no break the coaxial connexion hot glued on the VTX.
The unique butoon is installed on top.
The button if shorly pressed can cycle between the eight frequencies inside
the current selected band.
If you press on it more than 3S, the current band sign will flash
then short press on the button to cycle over the 12 bands !!!!.
Finally if you very long press on it, you will be able to cycle between
the three output power: 25mW (1 bar = default setting), 200mW (2 bars)
and 600mW (3 bars).
Video Format : NTSC/PAL
Channel: 40CH
Operating Temperature : -10~85℃
Connector: RP-SMA Female
Antenna connector: RP-SMA Male
Omnibus F4 V3 flight controller
Size: 36x36mm
Mount holes: 30.5x30.5mm
STM32 F405 MCU, Runs Betaflight 3.0.1 firmware, could run faster loop time.
Using F4 MCU controls OSD over SPI bus in DMA mode.
OSD Configation has been included in Betaflight GUI.
SBUS/PPM input (Pinheaders)
6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)
With barometer
SPI Sensor MPU6000
Included 128Mbit Flash, please always use BEC for the FC.
Supported by BETAFLIGHT and dRonin
Eachine 5051 3-blade propeller
Color: purple
Quantity: 10 Pairs
Mounting Hole: 5mm
This is the ARF version that comes without battery, charger, receiver and remote control.
Package included:
1 x Eachine Wizard X220S frame kit
2 x 2206 2300KV motor CW
2 x 2206 2300KV motor CCW
1 x Eachine 30A BLHELI_S 4 in 1 ESC
1 x Omnibus F4 V3 flight controller
1 x 1179 800TVL camera
1 x 5.8G 40CH 25MW 200mw 600MW switchable VTX
10 x Eachine 5051 3-blade propeller purple CW
10 x Eachine 5051 3-blade propeller purple CCW
1 x 30° Camera Mount(For Runcam3/Gopro session)
1 x Pagoda antenna
2 x Battery strap
2 x Wrench
(以下 参考データ）
ESC overview
CLI # diff all
diff all
# version
# Betaflight / OMNIBUSF4SD (OBSD) 3.5.6 Feb 16 2019 / 13:29:46 (c28ca22f9) MSP API: 1.40
board_name OMNIBUSF4SD
manufacturer_id
mcu_id 002b0049474b501620393257
signature
# reset configuration to default settings
defaults nosave
# name
name DRJ18_JE6RUX
# resources
# mixer
# servo
# servo mix
# feature
feature -RX_PARALLEL_PWM
feature -ANTI_GRAVITY
feature RX_SERIAL
feature LED_STRIP
# beeper
beeper -GYRO_CALIBRATED
beeper -ARMING_GPS_FIX
beeper -GPS_STATUS
beeper -ACC_CALIBRATION
beeper -ACC_CALIBRATION_FAIL
beeper -READY_BEEP
beeper -ARMED
beeper -ON_USB
beeper -BLACKBOX_ERASE
beeper -CRASH FLIP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSED
# beacon
# map
# serial
serial 5 64 115200 57600 0 115200
# led
led 0 0,0::CB:2
led 1 0,1::CB:2
led 2 0,2::CB:2
led 3 0,3::CB:2
led 4 0,4::CB:2
led 5 15,0::CB:2
led 6 15,1::CB:2
led 7 15,2::CB:2
led 8 15,3::CB:2
led 9 15,4::CB:2
# color
# mode_color
# aux
aux 0 0 0 1300 2100 0 0
aux 1 1 1 900 1300 0 0
aux 2 2 1 1300 1700 0 0
aux 3 13 3 1300 2100 0 0
aux 4 28 0 1700 2100 0 0
# adjrange
# rxrange
# vtx
# rxfail
# master
set serialrx_provider = SBUS
set osd_vbat_pos = 2081
set osd_tim_2_pos = 2103
set osd_flymode_pos = 2273
set osd_crosshairs_pos = 2253
set osd_craft_name_pos = 2497
set osd_warnings_pos = 2478
# profile
profile 0
# profile
profile 1
# profile
profile 2
# restore original profile selection
profile 0
# rateprofile
rateprofile 0
# rateprofile
rateprofile 1
# rateprofile
rateprofile 2
# rateprofile
rateprofile 3
# rateprofile
rateprofile 4
# rateprofile
rateprofile 5
# restore original rateprofile selection
rateprofile 0
# save configuration
save
#
スポンサーサイト
