やっとこさ届いた！BETAFPV８５X HD ヾ(￣∇￣=ﾉ ﾊﾞﾝｻﾞｰｲ

以前から、BETAFPV８５X　HD が欲しかったのですが、
メーカーに在庫が無くて、４Kを代りに買ってました。
が、先週、在庫を確認し発注してたのが、
今日、届きました。　ヾ(￣∇￣=ﾉ ﾊﾞﾝｻﾞｰｲ


　
まだ、何も設定していません。
ので、デフォルト状態です。　
（※　追記　）
# diff all
# version
# Betaflight / OMNIBUSF4SD (OBSD) 3.5.7 Mar 15 2019 / 22:11:36 (e9130527c) MSP API: 1.40

board_name OMNIBUSF4SD
manufacturer_id
mcu_id 001b00363339470838343535
signature

# reset configuration to default settings
defaults nosave

# name
name Beta 85X HD

# resources

# mixer

# servo

# servo mix


# feature
feature -RX_PARALLEL_PWM
feature RX_SERIAL
feature MOTOR_STOP
feature LED_STRIP

# beeper
beeper -ARMING_GPS_FIX
beeper -GPS_STATUS
beeper -READY_BEEP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSED

# beacon
beacon RX_LOST
beacon RX_SET

# map

# serial
serial 2 64 115200 57600 0 115200
serial 5 2048 115200 57600 0 115200

# led
led 0 0,0::A:0
led 1 1,0::A:0
led 2 2,0::L:0
led 3 3,0::L:0

# color

# mode_color
mode_color 6 0 2

# aux
aux 0 0 0 1300 2100 0 0
aux 1 1 1 900 1300 0 0
aux 2 2 1 1300 1700 0 0
aux 3 13 3 1300 2100 0 0
aux 4 28 0 1700 2100 0 0
aux 5 35 2 1300 2100 0 0

# adjrange

# rxrange

# vtx

# rxfail

# master
set acc_calibration = -116,111,-177
set mag_hardware = NONE
set baro_hardware = NONE
set fpv_mix_degrees = 35
set serialrx_provider = SBUS
set blackbox_device = NONE
set min_throttle = 1070
set use_unsynced_pwm = OFF
set motor_pwm_protocol = DSHOT1200
set motor_pwm_rate = 480
set ibatv_scale = 400
set beeper_dshot_beacon_tone = 5
set yaw_motors_reversed = ON
set small_angle = 180
set pid_process_denom = 1
set osd_warn_core_temp = OFF
set osd_vbat_pos = 2081
set osd_tim_2_pos = 2103
set osd_flymode_pos = 2273
set osd_throttle_pos = 321
set osd_current_pos = 352
set osd_mah_drawn_pos = 344
set osd_craft_name_pos = 2433

# profile
profile 0

set p_pitch = 55
set i_pitch = 85
set d_pitch = 29
set f_pitch = 96
set p_roll = 48
set i_roll = 80
set d_roll = 27
set f_roll = 96
set p_yaw = 60
set i_yaw = 77
set f_yaw = 100

# profile
profile 1


# profile
profile 2


# restore original profile selection
profile 0

# rateprofile
rateprofile 0


# rateprofile
rateprofile 1


# rateprofile
rateprofile 2


# rateprofile
rateprofile 3


# rateprofile
rateprofile 4


# rateprofile
rateprofile 5


# restore original rateprofile selection
rateprofile 0

# save configuration
save
#
（以上　追記）
　

---

---

---